Boilers

Introduction
The primary function of a boiler is to produce steam at a given pressure and temperature. To accomplish this, the boiler serves as a furnace where air is mixed with fuel in a controlled combustion process to release large quantities of heat. The pressure-tight construction of a boiler provides a means to absorb the heat from the combustion and transfer this heat to raise water to a temperature such that the steam produced is of sufficient temperature and quality (moisture content) for steam loads.

Boilers
Two distinct heat sources used for boilers are electric probes and burned fuel (oil, coal, etc.)This chapter will use fuel boilers to illustrate the typical design of boilers. Refer to Figure 9 during the following discussion.

The boiler has an enclosed space where the fuel combustion takes place, usually referred to as the furnace or combustion chamber. Air is supplied to combine with the fuel, resulting in combustion. The heat of combustion is absorbed by the water in the risers or circulating tubes. The density difference between hot and cold water is the driving force to circulate the water back to the steam drum. Eventually the water will absorb sufficient heat to produce steam.

Steam leaves the steam drum via a baffle, which causes any water droplets being carried by the steam to drop out and drain back to the steam drum. If superheated steam is required, the steam may then travel through a superheater. The hot combustion gasses from the furnace will heat the steam through the superheater's thin tube walls. The steam then goes to the steam supply system and the various steam loads.

Some boilers have economizers to improve cycle efficiency by preheating inlet feedwater to the boiler. The economizer uses heat from the boiler exhaust gasses to raise the temperature of the inlet feedwater.

Figure 9 Typical Fuel Boiler

Fuel Boiler Components
Figure 9 illustrates a typical fuel boiler. Some of the components are explained below.

Steam drum - The steam drum separates the steam from the heated water. The
water droplets fall to the bottom of the tank to be cycled again, and the steam leaves the drum and enters the steam system. Feedwater enters at the bottom of the drum to start the heating cycle.

Downcomers - Downcomers are the pipes in which the water from the steam drum travels in order to reach the bottom of the boiler where the water can enter the distribution headers.

Distribution headers - The distribution headers are large pipe headers that carry the water from the downcomers to the risers.

Risers - The piping or tubes that form the combustion chamber enclosure are called risers. Water and steam run through these to be heated. The term risers refers to the fact that the water flow direction is from the bottom to the top of the boiler. From the
risers, the water and steam enter the steam drum and the cycle starts again.

Combustion chamber - Located at the bottom of a boiler, the combustion chamber is where the air and fuel mix and burn. It is lined with the risers.

Boilers Summary
*Boilers are vessels that allow water in contained piping to be heated to steam by a heat source internal to the vessel. The water is heated to the boiling point. The resulting steam separates, and the water is heated again. Some boilers use the heat from combustion off-gasses to further heat the steam (superheat) and/or to preheat the feedwater.

*The following components were discussed:
The steam drum is where the steam is separated from the heated water.

Downcomers are the pipes in which the water from the steam drum travels to reach the bottom of the boiler.

Distribution headers are large pipe headers that carry the water from th downcomers to the risers.

Risers are the piping or tubes that form the combustion chamber enclosure. Water and steam run through the risers to be heated.

The combustion chamber is located at the bottom of the boiler and is where the air and fuel mix and burn.

Comments

M. Taufik said…
Nice artickle..

Just for sharing.. boiler can be classified not only by fuel, but also by using, pressure, tube type, material, circulation, combustion and so on. Boiler knowledge always be interesting lesson to be learned.

Regards,

M. Taufik
http://steamofboiler.blogspot.com/
Unknown said…
Great post...hope you provide more information. View more : Site Fabrication || Process Piping || Reaction Kettles || Heat Exchangers




really super boss

visit mine please
http://www.breakthroughmechans.blogspot.in/
http://www.breakthroughmechans.blogspot.in/
andersonherry said…
Amazing blog-post. I loved reading your blog post. You have shared very deep information on boiler. Every one cannot afford new boiler therefore Used boiler is also available.
You have shared very nice, precise and basic information about boilers. Really liked your blog. Keep sharing.
Boiler Engineer said…
thank you sir for nice boiler article
also visit my web for boilers
https://boilersinfo.com/
This is a necessary advice for a homeowner who wanted to install or repair its HVAC system. A very well written article. Heating and Cooling Hamilton
andersonherry said…
Such a nice blog and I appreciate your all efforts about your thoughts. It’s really good work. well done.

Boiler system

Great Post! Thanks for sharing good information with us. Please keep sharing.

Please visit Bunbury plumbing services

Popular Posts